
Speck Badu Top II/12, 1-phase
Speck BADU Top II/12 self-priming pool circulation pump, single-phase (230 V): shaft power 0.45 kW, built-in pre-filter, 2" / 1½" connection, can be installed up to 3 m above or below the water level.
VariantII/12, 1-phase
Description
The Speck BADU Top II/12 is a self-priming circulation pump that pushes pool water through the filtration system. The monobloc design has a built-in pre-filter basket and a mechanical seal on a plastic impeller hub. The single-phase motor (230 V) has a shaft power of 0.45 kW and a power input of 0.65 kW, and the maximum head is 15.5 m. According to Speck Nederland, the Top II/8–/14 series is intended for prefabricated (above-ground) and small pools with a volume of 30–90 m³.
Advantages
- Self-priming: may be installed up to 3 m above or below the water level
- The motor and pump shaft does not come into contact with the pool water, so the motor is electrically separated from the water
- Thanks to the high suction capacity, an automatic pool cleaner can be connected to the pump (Speck Nederland data)
- Polypropylene housing, carbon/ceramic/NBR mechanical seal
- Protection rating IP55, insulation class F, maximum water temperature 40 °C
In the box
- BADU Top II/12 pump
- Built-in pre-filter basket
- 3.5 m connection cable with plug
The pump must not run dry, as this can destroy the seal and plastic parts within a few seconds, nor with closed valves (the minimum flow rate is 10% of Qmax). The pipe dimensions from the datasheet apply to a suction line of up to 5 m; self-priming can take up to 12 minutes. Leave the electrical connection to an authorised electrician.
Specifications
| Flow rate | 8–14 m³/h (range for the whole Top II/8–/14 series) |
|---|---|
| Head | maximum 15.5 m |
| Power | 0.45 kW (P2, shaft power) |
| Power input | 0.65 kW (P1) |
| Voltage | 230 V, 50 Hz, single-phase |
| Current | 3.20 A |
| Connection | suction 2", pressure 1½"; recommended pipe Ø 50 mm (suction), Ø 50 mm (pressure) |
| Cable length | 3.5 m, with plug |
| Suction height | up to 3 m (pump above or below the water level) |
| Protection rating | IP55, insulation class F |
| Operating temperature | water up to 40 °C (GS approval) |
| Noise level | 57.7 dB(A) at a distance of 1 m |
| Length | maximum 485 mm |
| Weight | 9.6 kg |
| Material | polypropylene housing; carbon/ceramic/NBR mechanical seal |
Need advice?
Call us with your pool's dimensions — we will tell you which filter, pump or heater fits, and what goes with it.
+385 95 377 6396Message us on WhatsAppRelated products
What customers buy with this.

Pool filters
Aster filter D500, 9 m³/h, 1½" side connection
5 variants

Pool filters
Galactic monobloc filter D380, 5 m³/h
2 variants
Advice
Read before you buy.
Pool pump: how to choose the right one (filter pump)
A pump is chosen by flow, not motor power: about 12 m³/h for 8 × 4 × 1.5 m – and the upper limit is set by the filter and the pipes.

Sand vs quartz pool filter – which one filters better
‘Sand’ and ‘quartz’ filters are the same thing; the real choice is quartz sand (30–60 µm) or activated glass (down to 5 µm).

Sand filter pump for a pool: sizing and installation
A monobloc of pump, filter and valve: flow (volume × 2) ÷ 8, how much sand goes into the D400–D750 and where the unit may be installed.



