
Speck Badu Prime 25, 3-phase
Speck BADU Prime 25 self-priming pool circulation pump, three-phase (400/230 V): shaft power 1.30 kW, pre-filter of about 6 l, Ø 75 mm connection. Can be installed up to 3 m above or below the water level.
Description
The Speck BADU Prime 25 is a self-priming circulation pump from the Prime 25–48 series for larger pools; according to Speck Nederland, the series is intended for pools from 90 to 210 m³. The monobloc design has a built-in pre-filter of about 6 l, and the pump may be installed up to 3 m above or below the water level. The three-phase motor (400/230 V, Y/Δ) has a shaft power of 1.30 kW and a power input of 1.55 kW, and the maximum head is 18.2 m. The manufacturer states that the motor is suitable for operation with a frequency converter.
Advantages
- The motor and pump shaft does not come into contact with the pool water, so the motor is electrically separated from the water
- Mechanical seal with bellows on a plastic shaft protection sleeve (carbon/ceramic/NBR)
- Housing made of glass-fibre-reinforced polypropylene, impeller made of PPE GF 30, transparent pre-filter lid
- Protection rating IP55, insulation class F, maximum water temperature 40 °C
In the box
- BADU Prime 25 pump (three-phase version)
- Built-in pre-filter with basket and transparent lid (about 6 l)
- Tool for opening the pre-filter lid
- ABS fittings for gluing, Ø 75 mm
The manufacturer states the flow rate only for the whole series (Prime 25–48: 25–48 m³/h); check the operating point of the individual model in the performance chart. Recommended PVC pipe diameter: Ø 75 mm. Leave the electrical connection to an authorised electrician, and do not run the pump dry.
Specifications
| Flow rate | 25–48 m³/h (range for the whole Prime 25–48 series) |
|---|---|
| Head | maximum 18.2 m |
| Power | 1.30 kW (P2, shaft power) |
| Power input | 1.55 kW (P1) |
| Voltage | 400/230 V (Y/Δ), 50 Hz, three-phase |
| Current | 2.95 A (400 V) / 5.10 A (230 V) |
| Connection | Ø 75 mm (suction and pressure); ABS fittings for gluing are supplied |
| Pre-filter volume | about 6 l |
| Suction height | up to 3 m (pump above or below the water level) |
| Protection rating | IP55, insulation class F |
| Operating temperature | water up to 40 °C |
| Noise level | 65.1 dB(A) at a distance of 1 m |
| Length | maximum 795 mm |
| Weight | 26.1 kg |
| Material | pump housing PP GF 30, impeller PPE GF 30, transparent polycarbonate lid, stainless steel screws |
Documents
Need advice?
Call us with your pool's dimensions — we will tell you which filter, pump or heater fits, and what goes with it.
+385 95 377 6396Message us on WhatsAppRelated products
What customers buy with this.

Pool filters
Aster filter D500, 9 m³/h, 1½" side connection
5 variants

Pool filters
Galactic monobloc filter D380, 5 m³/h
2 variants
Advice
Read before you buy.
Pool pump: how to choose the right one (filter pump)
A pump is chosen by flow, not motor power: about 12 m³/h for 8 × 4 × 1.5 m – and the upper limit is set by the filter and the pipes.

Sand vs quartz pool filter – which one filters better
‘Sand’ and ‘quartz’ filters are the same thing; the real choice is quartz sand (30–60 µm) or activated glass (down to 5 µm).

Sand filter pump for a pool: sizing and installation
A monobloc of pump, filter and valve: flow (volume × 2) ÷ 8, how much sand goes into the D400–D750 and where the unit may be installed.



