
Speck Badu Prime 13, single-phase
Speck BADU Prime 13 self-priming pool circulation pump, single-phase (230 V): shaft power 0.55 kW, pre-filter of about 3 l, Rp 2 (suction) and Rp 1½ (pressure) connection. Can be installed up to 3 m above or below the water level.
Description
The Speck BADU Prime 13 is a self-priming circulation pump that pushes pool water through the filtration system. It is a monobloc design with a built-in pre-filter of about 3 l, and the pump may be installed up to 3 m above or below the water level. According to Speck Nederland, the Prime 7–20 series is intended for pools from 30 to 120 m³. The single-phase motor (230 V) has a shaft power of 0.55 kW and a power input of 0.72 kW, and the maximum head is 14.7 m.
Advantages
- The motor and pump shaft does not come into contact with the pool water, so the motor is electrically separated from the water
- Mechanical seal with bellows on a plastic shaft protection sleeve (carbon/ceramic/NBR)
- Housing and impeller made of glass-fibre-reinforced polypropylene, transparent pre-filter lid
- Protection rating IP55, insulation class F, maximum water temperature 40 °C
In the box
- BADU Prime 13 pump (single-phase version)
- Built-in pre-filter with basket and transparent lid (about 3 l)
- Tool for opening the pre-filter lid (universal)
The manufacturer states the flow rate only for the whole series (Prime 7–20: 7–20 m³/h); check the operating point of the individual model in the performance chart. Recommended PVC pipe diameter: Ø 63 mm on the suction side and Ø 50 mm on the pressure side. Leave the electrical connection to an authorised electrician, and do not run the pump dry.
Specifications
| Flow rate | 7–20 m³/h (range for the whole Prime 7–20 series) |
|---|---|
| Head | maximum 14.7 m |
| Power | 0.55 kW (P2, shaft power) |
| Power input | 0.72 kW (P1) |
| Voltage | 230 V, 50 Hz, single-phase |
| Current | 3.50 A |
| Connection | suction Rp 2, pressure Rp 1½ (internal thread); recommended PVC pipe Ø 63 mm (suction), Ø 50 mm (pressure) |
| Pre-filter volume | about 3 l |
| Suction height | up to 3 m (pump above or below the water level) |
| Protection rating | IP55, insulation class F |
| Operating temperature | water up to 40 °C |
| Noise level | 52.3 dB(A) at a distance of 1 m |
| Length | maximum 507 mm |
| Weight | 11.8 kg |
| Material | pump housing and impeller PP GF 30 (glass-fibre-reinforced polypropylene), transparent polycarbonate lid, stainless steel screws |
Documents
Need advice?
Call us with your pool's dimensions — we will tell you which filter, pump or heater fits, and what goes with it.
+385 95 377 6396Message us on WhatsAppRelated products
What customers buy with this.

Pool filters
Aster filter D500, 9 m³/h, 1½" side connection
5 variants

Pool filters
Galactic monobloc filter D380, 5 m³/h
2 variants
Advice
Read before you buy.
Pool pump: how to choose the right one (filter pump)
A pump is chosen by flow, not motor power: about 12 m³/h for 8 × 4 × 1.5 m – and the upper limit is set by the filter and the pipes.

Sand vs quartz pool filter – which one filters better
‘Sand’ and ‘quartz’ filters are the same thing; the real choice is quartz sand (30–60 µm) or activated glass (down to 5 µm).

Sand filter pump for a pool: sizing and installation
A monobloc of pump, filter and valve: flow (volume × 2) ÷ 8, how much sand goes into the D400–D750 and where the unit may be installed.



